Knowledge Base

Articles

Fiber Strength Testing: Glossary and Key Facts

Key terms, definitions, and facts for fiber strength and material performance testing in paper and pulp manufacturing. 

Key Terms

Zero-Span Tensile Strength

The breaking strength of a paper sample measured at zero (or near-zero) gauge length. Isolates the intrinsic tensile strength of individual pulp fibers from inter-fiber bonding effects. Measured to TAPPI T231. Expressed in kN/m or as a tensile index (kN/m divided by grammage). 

Tensile Index

Zero-span or conventional tensile strength normalized by the grammage (basis weight) of the paper sample. Expressed in Nm/g. Enables direct comparison between sheets of different weights. Standard calculation: breaking force (kN/m) / grammage (g/m2) x 1000.

Short-Span Tensile (SST)

A variation of zero-span testing where a small but defined gauge length (typically 2 mm) is used. Captures a combination of fiber wall strength and short-range bonding. Relevant for predicting runnability on printing and converting equipment.

TAPPI T231

The TAPPI T231 standard governs zero-span breaking strength of pulp in a handsheet. Defined by TAPPI International. Applies to bleached and unbleached chemical pulps, mechanical pulps, and recycled fiber grades. Key parameter measured: zero-span tensile strength.

TAPPI T494

Standard test method for tensile breaking strength and elongation of paper and paperboard. Uses a 100 mm or 180 mm gauge length. Measures sheet tensile strength, including the contribution of fiber bonding and sheet structure.

ISO 1924

International standard for determining the tensile properties of paper and board. ISO 1924-2 covers the constant rate of elongation (CRE) method at 20 mm/min, while ISO 1924-3 covers the CRE method at 100 mm/min. These standards are widely used alongside TAPPI T494 for cross-reference and international compliance.

Wet Tensile Strength

The tensile strength of paper measured after saturation with water. Critical for applications where paper will be exposed to moisture – tissue, release liners, food-contact packaging. Measured by wetting samples to defined saturation levels before testing.

Hornification

The stiffening and loss of swelling capacity of cellulose fibers following drying and rewetting cycles. Causes reduced fiber bonding potential and lower tensile strength in recycled fiber grades. A key quality concern in recovered paper processing.

Grammage

The mass per unit area of a paper sheet, expressed in g/m2 (grams per square meter). Closely related to basis weight. Used to normalize tensile strength measurements to produce tensile index values that are independent of sheet weight.

Was this useful?

FAQs

  • Zero-span tensile strength is a measure of the intrinsic tensile strength of pulp fibers within a paper sheet. The test is performed by clamping a paper sample at zero gauge length – meaning the two gripping jaws are positioned directly opposite each other with no free span between them. When force is applied, only the fibers spanning the clamp boundary are loaded, which isolates fiber wall strength from the influence of inter-fiber bonding and sheet structure. 

    This distinction is critical because conventional tensile tests (such as those to TAPPI T494 or ISO 1924) measure the combined effect of fiber strength and bonding. Two pulp furnishes can produce paper with the same sheet tensile strength but significantly different fiber quality – a difference invisible to conventional testing but clearly identified by zero-span. 

    Zero-span testing is governed by TAPPI T231 and is used across pulp mills, paper manufacturers, and R&D laboratories for incoming pulp quality control, refining optimization, and new grade development. The Technidyne Pulmac Automated Z-Span™ Fiber Strength Tester automates this measurement, reducing operator variability and increasing testing throughput. 

  • The Technidyne Pulmac Automated Z-Span™ Fiber Strength Tester is a purpose-built instrument for zero-span and short-span tensile testing of paper and pulp samples in accordance with TAPPI T231 and related standards. 

    The system automates the full test sequence – from sample transport and positioning to clamping and load application – eliminating the manual handling steps that traditionally introduced variability into zero-span measurements. 

    Key operational features include: 

    • Automated sample feeding – strips are loaded and advanced through the test zone without manual intervention 
    • Precision pneumatic jaw clamping – controlled clamping pressure ensures repeatable grip contact across all test strips 
    • Wet and dry testing modes – supports both conditioned dry-tensile and wet-tensile specimen testing 
    • High throughput – automation allows significantly more tests per hour compared to manual methods 
    • Integrated data output – results including mean breaking force, tensile index, and statistical variation are reported automatically 

    The instrument is designed for use in QC laboratories within pulp mills and paper manufacturers, as well as in R&D environments. For more information, visit the product page or explore the broader Technidyne paper testing range. 

  • Zero-span and conventional tensile testing both measure the force required to break a paper sample, but they measure fundamentally different material properties. 

    Conventional tensile testing (TAPPI T494, ISO 1924) uses a gauge length of 100 mm or 180 mm. The sample is loaded across this distance and fails at its weakest point. The result reflects the combined contribution of fiber strength, fiber bonding, fiber length distribution, and sheet formation – a measure of overall sheet tensile performance. 

    Zero-span tensile testing (TAPPI T231) uses a gauge length of zero or near-zero. By gripping the sample at a single point from both sides, only the fibers crossing the clamp boundary are loaded. This removes bonding from the equation entirely, delivering a direct measurement of fiber wall tensile strength. 

    The practical implication is significant: zero-span testing diagnoses the root cause of strength differences, while conventional tensile testing reflects the end result. 

    Both test types are available within the Technidyne paper and pulp testing portfolio from Industrial Physics. 

  • Fiber tensile strength testing is relevant across the full paper and pulp supply chain: 

    • Pulp mills – monitor fiber quality throughout kraft, mechanical, and recycled pulp production; detect the impact of cooking, bleaching, and refining on fiber integrity 
    • Corrugated and containerboard manufacturers – high fiber tensile strength is essential for box compression performance; strength testing supports lightweighting initiatives without sacrificing structural integrity 
    • Tissue and hygiene producers – balance fiber strength with softness and absorbency requirements; wet tensile testing is particularly important for products that must maintain integrity when wet 
    • Printing and writing paper producers – ensure adequate tensile strength to prevent web breaks during high-speed printing and converting 
    • Recycled fiber processors – fiber strength declines through repeated recycling cycles; testing identifies when fiber quality falls below acceptable thresholds 
    • R&D and product development teams – zero-span testing supports new grade development, sustainability programs, and fiber optimization projects 

    Industrial Physics supports paper and pulp manufacturers across all these applications through the Technidyne testing portfolio. For paper and pulp testing solutions, explore the full range here. 

Related Articles